part of
by Rick Curtis
published by Random House 1998
This material is taken from Chapter 6 - Wilderness Travel from The Backpackers Field Manual by Rick Curtis. For more details on this exciting book check out The Backpacker's Field Manual Page.
This material is provided by the author for educational use only and is not a substitute for specific training or experience. Princeton University and the author assume no liability for any individual's use of or reliance upon any material contained or referenced herein. When going into outdoors it is your responsibility to have the proper knowledge, experience, and equipment to travel safely. This material may not be reproduced in any form for commercial or Internet publication without express written permission of the author. Copyright © 1999, all rights reserved, Random House Publishing & Rick Curtis, Outdoor Action Program, Princeton University.
Traveling anywhere in the wilderness means determining where you want to go. Maps and guidebooks are the fundamental tools both for trip planning see (Chapter 1 - Trip Planning) and while you are out on the trail.
A map is a two-dimensional representation of the three-dimensional world you'll be hiking in. All maps will have some basic features in common and map reading is all about learning to understand their particular "language." You'll end up using a variety of maps to plan and run your trip but perhaps the most useful map is a topographic map. A topographic map uses markings such as contour lines (see page 00) to simulate the three-dimensional topography of the land on a two-dimensional map. In the U.S. these maps are usually U.S. Geological Survey (USGS) maps. Other maps that you'll find helpful are be local trail maps which often have more accurate and up-to-date information on specific trails than USGS maps do. Here's a brief overview of the basic language of maps.
Maps are drawn based on latitude and longitude lines. Latitude lines run east and west and measure the distance in degrees north or south from the equator (0° latitude). Longitude lines run north and south intersecting at the geographic poles. Longitude lines measure the distance in degrees east and west from the prime meridian that runs through Greenwich, England. The grid created by latitude and longitude lines allows us to calculate an exact point using these lines as X axis and Y axis coordinates.
Both latitude and longitude are measured in degrees (°).
1° = 60 minutes
1 minute = 60 seconds
Therefore:
7 ½ minutes = 1/8 of 60 minutes = 1/8 of a
degree
15 minutes = ¼ of 60 minutes = ¼ of a degree
All maps will list their scales in the margin or legend. A scale of 1:250,000 (be it inches, feet, or meters) means that 1 unit on the map is the equivalent of 250,000 units in the real world. So 1 inch measured on the map would be the equivalent of 250,000 inches in the real world. Most USGS maps are either 1:24,000, also known as 7 ½ minute maps, or 1:62,500, known as 15 minute maps (the USGS is no longer issuing 15 minute maps although the maps will remain in print for some time).
Standard topographic maps are usually published in 7.5-minute quadrangles. The map location is given by the latitude and longitude of the southeast (lower right) corner of the quadrangle. The date of the map is shown in the column following the map name; a second date indicates the latest revision. Photo-revised maps have not been field checked.
| Map Size | Scale | Covers | Map to Landscape | Metric |
|---|---|---|---|---|
| 7 ½ minute | 1:24,000 | 1/8 of a degree | 1 inch = 2,000 feet (3/8
mile) 2.64 inches = 1 mile |
(1 centimeter = 240 meters) |
| 15 minute | 1:62,500 | ¼ of a degree | 1 inch = ~1 mile | (1 centimeter = 625 meters) |
Courtesy US Geological Survey
Courtesy US Geological Survey
The map legend contains a number of important details. The figures below display a standard USGS map legend. In addition, a USGS map includes latitude and longitude as well as the names of the adjacent maps (depicted on the top, bottom, left side, right side and the four corners of the map). The major features on the map legend are show in Figure 6.3 and labeled below.
Contour lines are a method of depicting the 3-dimensional character of the terrain on a 2-dimensional map. Just like isobars in the atmosphere depict lines of equal atmospheric pressure, contour lines drawn on the map represent equal points of height above sea level.
Look at the three-dimensional drawing of the mountain below. Imagine that it is an island at low tide. Draw a line all around the island at the low tide level. Three hours later, as the tide has risen, draw another line at the water level and again three hours later. You will have created three contour lines each with a different height above sea level. As you see in Figure 6.4, the three dimensional shape of the mountain is mapped by calculating lines of equal elevation all around the mountain, and then transferring these lines onto the map.
On multi-colored maps, contour lines are generally represented in brown. The map legend will indicate the contour interval—the distance in feet (meters, etc.) between each contour line. There will be heavier contour lines every 4th> or 5th contour line that are labeled with the height above sea level. Figure 6.5 illustrates how a variety of surface features can be identified from contour lines.
3D View of Mountain showing how contours relate to height
Top View of Mountain showing contours
Drawn Contour Lines
There are a number of ways to measure distance accurately on a map. One is to use a piece of string or flexible wire to trace the intended route. After tracing out your route, pull the string straight and measure it against the scale line in the map legend. Another method is to use a compass (the mathematical kind) set to a narrow distance on the map scale like ½ mile and then "walk off" your route. It is a good idea to be conservative and add 5-10% of the total distance to take into account things like switchbacks that don't appear on the map. It's better to anticipate a longer route than a shorter one.